Chico Slot Car Racing Club - Chico, Calif.

The Chico Slot Car Racing Club Presents:

The 2nd Annual, 2002

6 Hour Petite Lemans

ENDURO de CHICO

RULES / SPECS

---

CLASS NAME:  FLEXI/LMP  

MOTOR/GEARS:  C can w/ balanced Super Wasp/Hornet armature .513" dia. min. (new lightened Kelly and RJR can not permitted). 

 1) Lead wires may be changed.
 2) Motor case may be ground slightly to clear rear axle and/or bushings.
 3) Armature shaft may be shortened.
 4) Motor can may be soldered to top of chassis motor bracket and soldered to the chassis center section, or braced with 0.062" piano wire.  
 5) Any pitch spur gear and pinion.
 6) Brushes and springs may be changed.
 7) Any ceramic magnet for C cans, may be glued in w/ super glue or Locktite, no  shimming allowed.
 8) NO OTHER MODIFICATIONS ALLOWED.  

CHASSIS:  Approved production 4" wheel base 2 piece stamped steel Flexi type chassis:  Parma Flexi I, II, III; Champion Astro, Turbo Flex; RJR Roadrunner; Slotworks Spyder, Spyder 2000.  No prototypes.   Aluminum pans OK.

1) One commercially available guide flag, any manufacturer.
2) Front wheels/tires, minimum diameter 1/2".  Front wheels must touch and roll when car tips before any other part of the car touches the track (excluding guide flag and braid).  No sticker or flimsy rubber front wheels.
3) Front axle:  .062" dia. piano wire, may be soldered to front axle uprights.
4) Rear axle bushings:  Any 3/32" I.D. oilite bushings.  May soldered or glued.  Ball bearings not allowed.
5) Any commercially available black rear tire,  maximum tire width .810". 
6) Rear Axle: 3/32" diameter drill blank axle.  Hollow or filled axles not allowed.
7) Motor bracket may be filed to clear motor bushing but may not be removed. 
8) Chassis Bracing:  A single .062" U shaped piece of piano wire or Slick 7 P/N S7-390 may be soldered to rear axle bushing uprights.  Axle tubes not allowed. 
9) NO CUTTING/LIGHTENING OF CHASSIS except as described above.

BODIES LMP (LeMans prototype):  Approved JK Products bodies - 7176 Toyota, 7177 BMW, 7178 Porsche, 7182 Audi, 7183 Mercedes, 7184 BMW, 7185 Cadillac, 7186 Panoz, 7187 Lola-Judd, 7191 Sintura, 7192 Audi, 7193 Reynard, 7194 Chrysler, 7195 Courage, 7196 Panoz, 7197 Bentley, 7198 MG-Lola, 7199 Dome, 7200 Ascari.  Body must be trimmed to the manufacturers molded in "cut line".    0.007" or 0.01" thickness OK.

1) May be mounted with body clips or straight pins and stainless steel or brass pin tubing soldered to pan or floating type.
2) Front wheel area must be cutout or left clear so front wheels are fully visible.
3) May be painted any color scheme desired but paint must be opaque (no thin mist paint jobs allowed) and have a minimum of three racing numbers.
4) Interior must be 3D painted and detailed. No paper interiors.
5) Interior and body must cover all of chassis, wheels and guide flag when viewed from above. 

GROUND CLEARANCE:  Minimum 0.063" at the rear of chassis including the spur gear.
MAXIMUM BODY HEIGHT:  Body must be cut along mfrs. "cut line" front, rear and sides.
MAXIMUM WIDTH:  3-1/4" measured from edge to edge across rear tires and wheels.

---

For more information and entries call:

Todd Radke - days (530) 898-9895,  eves (530) 894-0587
email: todd@atchardwaresystems.com

CLICK HERE FOR ENDURO de Chico RACE INFO